Heat therapy is beneficial for a number of different therapies. It can be used at home to treat minor discomfort or it can be used post-operatively as a way to increase blood flow to a certain area to aid in healing. The most effective moist heat methods are those that can maintain an appropriate temperature on their own without burning the patient while still providing enough heat for effectiveness. Ultimately you want the temperature to be warm enough to be absorbed deep down into the muscular level and moisture can help with this process.
Moist heat and dry heat are both used for heat therapy. Dry heat is usually administered by way of an electric heating pad, sauna, etc. This therapy is designed to draw moisture out of the body and some people find it more comfortable and helpful. Moist heat on the other hand, is applies through a moist heating pack, hot bath or hot water bottle. Moist heat tends to provide more relief on a deeper level and is a bit easier to provide consistent temperatures.
Moist heat can be included in custom trays and can be applied a number of ways. These methods include:
A medical professional can always advise the best ways to utilize moist heat methods no matter what the need may be. The duration that the heat should be applied as well as the frequency varies with each injury and is based off the magnitude of the issue. Usually, fifteen to twenty minutes is the amount of time that moist heat methods are applied; every two to three hours. Custom trays in medical facilities can include moist heat packs for post operative use to keep patients comfortable and promote healing faster. There are instances when cold therapy is recommended as well. Sometimes medical professionals like to alternate these treatments. For outpatient therapy, many patients have a preference when it comes to heat therapy and sometimes it takes trial and error to find out what will work the best for long term relief.
Image is from Healthcare Purchasing News
A custom surgical tray is one of the most crucial equipment in a hospital setup. Essential as it is, this equipment should be taken care to enhance their longevity. Taking care of surgical instruments before keeping them is the surest method of protecting your tools. The ones that take care of properly last longer. Proper storage of instruments comes after you have properly cleaned them.
Preparation for storing the tray involves three levels;
This is the initial step of storing your tray. Ensure you clean all the body fluids, blood, and other tissues. Dirt like dry soil may even damage your tray or make it tough to use. After washing, rinse the tray in cold, clean water. Avoid using hot water as it can cause protein substances to coagulate. You can soak the tray in cold water mixed with an enzymatic detergent. The detergent will help in dissolving the proteins on the instrument surface as well as breaking the oils. After that, you can now clean the tray in cold water manually. If there as an alternative for manual cleaning like mechanical cleaning, you can opt for it. Normally, mechanical washing involves the use of a washing machine to wash the tray. The machine cleans through multiple levels. Cold water is for removing the debris. Then a hot water bath followed by a blow dry with hot air. Use gloves as you do the cleaning, plastic apron, eye protection and a mask.
For high-level disinfection, both thermal are available. Boil the instrument in a 100 degrees water for some time, preferably one minute. Only some few bacterial spores don’t die during the boiling; it is imperative to remember that boiling will not sterilize equipment. Just submerge the tray into the boiling water. When you notice the temperature of the water exceeding one hundred degrees, turn down the heat so it can boil gently. After a minute, remove the instrument from the boiling water using a pair of disinfected tongs. It is important to remember here not to remove the tray in the water as it cools since it can be decontaminated.
Sterilization does away with all microorganisms. Autoclaving is a common method of sterilizing this equipment. However, you can use dry heat or chemical sterilants.
Cleaning is meant to remove dirt and other biological material that may have been present on the tray’s surface. It is easy to clean these instruments manually or using mechanically using water, detergent, and other enzymatic materials. Cleaning it thoroughly since biological materials can remain on the surface to and be a hindrance to subsequent steps of sterilization and disinfection.
Disinfecting this equipment can be done in multiple levels including; low-level disinfection, intermediate level disinfection and high-level disinfection.
Sterilization kills all microorganisms certain chemical sterilants can be used as HLD disinfectants when used for shorter exposed durations. You can use autoclaving to do the disinfection.
After all the cleaning, disinfection, and sterilization, keep your tray in a place where they are not exposed to any more dirt and contaminants. If you don’t maintain the tray a safe place, you are going to pose a great danger in infecting the patient.
Image is from Medline.com
A custom tray is a medical equipment that requires you to sterilize so as to kill the bacteria and other disease-causing organisms present on the surface. If left unsterilized, the patient could be exposed to several harmful microorganisms which may end up causing more harm. As such, a custom tray has to be free from germs always and more especially during the procedure. Sterilization of a custom tray can be achieved in two ways:
Despite being a method that has been used for many years, dry heat method has often been misunderstood. Unlike in moist heat sterilization method where high temperature is used in performing sterilization, here heated air is used to achieve the same. Additionally, the temperatures in this method are relatively higher than in the moist heat method. The disease-causing microorganisms are killed through the destructive oxidation process. This process helps to terminate large biomolecules such as proteins. The organism will eventually die due to the destruction of some of the most vital components of the cell. It is, however, most suitable for the equipment which is resistant to heat
For moist heat sterilization, water at high-pressure level is used for sterilizing instruments like a custom tray, and the process is carried out in autoclaves. Although the temperature of steam in this method of sterilization is relatively lower than its dry heat counterpart, the pressure helps to effect sterilization properly. The moist heat destroys the structural proteins of the disease-causing organism on the surface of a custom tray. Eventually, this results in the death of the organisms on the surface of the custom tray. This method is effective in that it takes a shorter time to complete the whole sterilization process and in low temperatures too.
While you can achieve the same results in many loads, including a custom tray, with both methods, certain tasks are impossible while using a steam autoclave like loads that are hydrophobic or ones that will be damaged when exposed to moisture. As well, dry heat is useful for instruments such as a custom tray, which may experience corrosion.
Even as you can use dry heat method on a myriad of equipment, including a custom tray, it is, by no means, all purpose. Liquids, for instance, unlike a custom tray, cannot be sterilized using the method and neither can be growth media. Unlike a custom clay, dense loads are a problem too since the convection process does not penetrate them.
Although many loads like a custom tray can be sterilized by using either moist or dry heat, steam sterilizers consume less time and energy compared to dry heat. For a resistant spore to be killed by dry heat, the load in a dry heat sterilizer must be brought to 170 degrees centigrade and maintained there for as long as one hour. On the other hand, a steam autoclave only needs to be raised to 121 degrees centigrade for as short as fifteen minutes. This is because the steam is an excellent conductor of heat and is, therefore, able to permeate loads. As a result, there is significant cost saving when you use a steam heat sterilizer compared to dry heat sterilizer.
The above are some of the basic differences between dry and moist heat sterilization methods. Using either of them, ensure your equipment are properly sterilized. A custom tray is particularly one instrument you don’t want to forget to sterilize.
Heat therapy is beneficial for a number of different therapies. It can be used at home to treat minor discomfort or it can be used post-operatively as a way to increase blood flow to a certain area to aid in healing. The most effective moist heat methods are those that can maintain an appropriate temperature on their own without burning the patient while still providing enough heat for effectiveness. Ultimately you want the temperature to be warm enough to be absorbed deep down into the muscular level and moisture can help with this process.
Moist heat and dry heat are both used for heat therapy. Dry heat is usually administered by way of an electric heating pad, sauna, etc. This therapy is designed to draw moisture out of the body and some people find it more comfortable and helpful. Moist heat on the other hand, is applies through a moist heating pack, hot bath or hot water bottle. Moist heat tends to provide more relief on a deeper level and is a bit easier to provide consistent temperatures.
Moist heat can be included in custom trays and can be applied a number of ways. These methods include:
A medical professional can always advise the best ways to utilize moist heat methods no matter what the need may be. The duration that the heat should be applied as well as the frequency varies with each injury and is based off the magnitude of the issue. Usually, fifteen to twenty minutes is the amount of time that moist heat methods are applied; every two to three hours. Custom trays in medical facilities can include moist heat packs for post operative use to keep patients comfortable and promote healing faster. There are instances when cold therapy is recommended as well. Sometimes medical professionals like to alternate these treatments. For outpatient therapy, many patients have a preference when it comes to heat therapy and sometimes it takes trial and error to find out what will work the best for long term relief.